Level 4-3: Assemble Ranged Weapon

18 Feb

Hola fellow Cosplayers! Daniel here! With only two short months or a little over 8 measly weeks from C2E2, the stress has definitely kicked up ten fold with the announcement of The Crown Championships of Cosplay!

What-the-what!? A major cosplay contest at the event where we plan to unveil our first serious cosplay venture!? With Yaya Han as a judge!? Yaya Han!?!?!?

 Bring it on!!!

With Eleanor Lamb’s syringe built, it was time to take a crack at her secondary weapon – the harpoon. There are actually very few reference photos for the design and look of the harpoon and game play references weren’t much help either. So we had to piece together our best interpretation of it based on the couple of sources we had and other peoples’ takes. You can see a little bit of the harpoon on the left hand in the reference picture.

Eleanor Lamb screen shot

Eleanor Lamb's Harpoon MatterialsWe again started by cutting a large PVC tube in half to serve as the base for the harpoon mechanism. Sara sanded down and rounded the edges to make for a more comfortable fit. We then attached a 1 ½ ft. long section of 1” PCV pipe to the top of the base to serve as the ‘gun barrel’ for the harpoon itself.

Body of Eleanor Lamb's Harpoon

We fixed a decorative PCV cap on the front of the barrel and decorative PVC connector (that looks like a loading port) to the back-end of the barrel. We then drilled a hole in the front cap to feed the harpoon through.

All in all, the harpoon was starting to shape up nicely, but I wasn’t convinced that we had it looking like it was ‘functional’ as the syringe. What we needed was a ‘compression-chamber-looking-device’ that would give the appearance that the harpoon had propellant capabilities.

Sara dashed my first idea to pieces, which was to have the harpoon barrel feed into a shorter, squatter section of PVC tubing positioned at the back of the barrel to look like a  mini-propane tank. Her concern was that it would look too bulky and would be a hassle to tote around all day. She was quite right.

Eleanor Lamb's Harpoon TriggerI decided that the best solution was not one large chamber positioned at the back, but two, smaller chambers arranged on either side.  I took some of our extra 1/2” wooden dowel rod  and cut two identical ‘tubes’ with a 45 degree angle cut at one end.  I then fixed a tube to each side of the barrel and viola! But how does this thing ‘fire?’ We decided to construct a button mechanism to rear portion of the barrel.

We started by gluing one of our smaller Plastic Insulated Bushings to the top of the barrel. However, the circumference of the bushing was slightly wider than the PVC barrel and hung out to the sides. To correct this I constructed a foam housing to straddle the barrel and wrap around the excess bushing.

Button for Harpoon TriggerWe then used the top cap from an old floor lamp as the actual button itself. It resulted in a rather impressive looking button element!

For an added bit of flair we also added a ‘sight’ to the front end of the barrel to even out the design. Luckily our package of flex tubing came with a nifty little plastic connector that did just the trick!

Eleanor Lamb's Harpoon Body

Lastly was the harpoon itself! I started by cutting a 2 ½ ft. section of  ¼” dowel rod. I then sanded down the tip to a rounded point.  Now the hard part – the harpoon blades or barbs as they are sometimes called. Which… in hindsight weren’t so hard after all. See what I did with that ellipses there? I’m so tricky! I started by cutting three ¼” slender parallelograms from 2mm foam. I then notched out three slots in the harpoons shaft using our X-acto knife and hot glued them into place.

Foam Blade Shape

And there you have it – a pretty darn good harpoon if I do say so myself!

After a bit of painting well fix it up with some leather arm straps and we’ll be set!

Eleanor Lamb's Harpoon

Here’s an action shot complete with Eleanor Lamb’s helmet, syringe and harpoon to tide you over while we get back to work as there is still so little to do and so much time. Wait… strike that, reverse it. — TCG

Eleanor Lamb Helmet and Weapons

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: