Level 5-2: Attach Accessories

18 Jun

Is that a club on your hip or are you just happy to see me?

With Subject Delta’s suit near completion, it was time for some finishing details! What’s a suit without accessories?

 

Subject Delta Action Figure Front

If you’ll notice in the reference above, there’s a club of sorts hanging from Delta’s hip. It appears to be a wooden cudgel, the kind akin to a tire thumper like truck drivers use to check their tires. Delta and the Big Daddies use theirs to check underwater pipes.

For the shaft… Ha! I said shaft… we used a 3/4″ inch dowel rod. I cut the length to about 12″ and then cut one end with a series of angles to form a rough point.

IMG_0650 IMG_0651

                                                                                                                                                                                                                                                                                                                     I then sanded the rough point down to a smooth, rounded knob… HA! Knob, this is too easy… and then sanded the opposite, flat edge to round the edges just slightly.  Next, I created a hand guard using a wooden napkin ring and a crafted foam piece.

IMG_0646

IMG_0649 IMG_0648

 The foam piece took some finagling as the template for a circular trapezoid; or cone without a top, is actually a rainbow shape. Using 2 mm foam, I cut out the rainbow piece and a circular doughnut for the cap. I glued them together with hot glue and attached it to the wooden napkin with hot glue as well.

IMG_0652

Look at how nicely that fits! You’ll also notice that there are a series of rings notched into the handle of the club.  I free-handed the rings with a pencil and then used the hand saw to cut about 3/8″ into the handle to create the grip. With the basic pieces complete, it was time to give them some color. For the club itself I used a dark walnut stain. I painted the stain on with a paint brush, let it set for 2-3 minutes and then wiped it off with paper towels.

IMG_0666 IMG_0667

IMG_0668 IMG_0669

For the hand guard, I coated the foam piece with a few layers of shellac and then hit it with some of the Antique Brass spray paint.

IMG_0656

After the pieces dried properly, I fixed the hand guard in place with a bit of wood glue, used some black acrylic paint to weather it and viola! Finished Big Daddy, pipe-thumping club!

IMG_0671 IMG_0670

To attach the club to the suit, I fashioned a sort of holster out of some of our left-over leather. I started by cutting a rectangle section to serve as a base. I stitched the piece like we did with our straps for consistency. I then cut and stitched another, longer and wider rectangle and attached it to the first to form a leather tube. I hot glued the pieces together and spot stitched them for added strength. I then hot glued the combined holster to the suit along the edge of one of the straps and spot stitched it as well.

IMG_0924 IMG_0925

Sara suggested gluing the cudgel into the holster. She was worried that it might fall out and I, with my mobility limited in costume, might not be able to put it back in. But, after reading over the C2E2’s weapon’s policy, I wanted to be able to remove it in case security wanted to take it away. Shows you what newbies we were, worried about a small wooden club. Ha! Ultimately, we didn’t have a single problem.

The other element you’ll notice from the above shots, is the elbow pad. I built one for the non drill arm and two similar, slightly larger pads for the knees. I started off with a basic elbow/knee pad from Home Depot. The pads were an ideal base; sturdy and durable with a built-in elastic strap. They were a perfect anchor to build onto. One edge of the pad is flat and the other rounded; but if you’ll notice, Subject Delta’s pads are rectangular. So, I took out my handy-dandy hand saw and cut off the rounded edge.

IMG_0589 IMG_0590

With the pads cut to the proper shape, I measured and cut out a strip of leather to face them with. Before attaching the leather, we hand stitched it with some of our yellow detail thread. I then hot glued the leather to the pads, around the sides and anchored the edges around the backside cutting slits at the edges to allow for the elastic strap. To finish off the tops and bottoms of the pads I stood the pads on end and traced the shape to get perfect curved shapes to hot glue in place.

knee pad IMG_0626

The next step was to build the metal platting attached to the pads. I used some 2 mm craft foam and cut out three rectangle pieces with curved edges to match the shape of the pads. I then used the hole punching tool from our grommet set to punch out some foam circles to serve as “rivets” for the corners.

IMG_0815

I hot glued the ‘rivets’ into place, sealed the foam with a couple of layers of watered-down Elmer’s glue,  applied a few layers of Shellac and then sprayed the plates with some of the Antique Brass spray paint. Once the plates were complete, I hot glued them to the pads. Sadly, the hot glue was not strong enough to adhere the plates to the faux leather pads. So, I pulled the plates off and peeled off the useless hot glue. After a couple of days of brainstorming and trying to figure out what adhesive would work best, I remembered the stuff I used to reattach the soles of my sneakers… SHOE GOO!!! This stuff is amazing and I plan to use it for this and future projects. Since it’s made for shoes, it’s perfect for adhering wildly different types of materials together. It’s perfect for attaching more substantial elements to fabric pieces while still remaining playable. You just smear the stuff to both sides of whatever you want to glue together and let it sit for a while, get good and tacky and then put it together. We let it cure for 24 hours and it worked perfectly!

IMG_0747

After all of the plates had time to properly dry, I then took some of our black acrylic paint and weathered them.

IMG_0922 IMG_0923

Last but not least, I detailed the suit. I laid it out on the floor and took some time weathering it with some of the black acrylic paint. I made sure to grime up the zippers that ran along the outer seam of the legs, as well as all around the strapping and patches.

IMG_0885

What started on a pretty basic work-suit and now, after some dressing and distressing, we’d wound up with a pretty fantastic looking suit!

Photo by: Geek Behind the Lens Photography

Photo by: Geek Behind the Lens Photography

Thank you for following along as we crafted Subject Delta’s suit! — TCG

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: